Iprog read MC68HC705B32 (UCH) possible and how?

 How to read MC68HC705B32 (UCH) on the Megane in circuit with Iprog programmer?

the diagram that the iprog says it is to read the processor, but the cable from pins 1, 5 and 40 has no connection and as the wire cores are not like the diagram.

Get a multimeter and test what colour wire goes to each pin on adapter then write it down 

then you will see what colours corispond to the colours you need if there then found to not be connected to the pins you need then get a soldering iron and move the wires to the correct pins 

if you cant solder then get someone who can to do it for you.

Iprog tech support: https://www.obd2shop.co.uk/

HW V5.017 SW V2.53 KESS V2 Wake Up Error Solution

 Offer the working solution to HW V5.017 SW V2.53 KESS V2 Wake Up Error.

Possible reason and solution:

It may be a gasoline car, and the customer chooses a diesel car.

please check the connection with ECU and power supply. And also try to uninstall the software and install it again.

If all is ok and still same error, please try rearranging the sd (TF)card in slot. I got resoldered the main components on the pcb and it worked ok. The issues with this cloned kess are few(bad contacts, need to rewrite the content of sd card or need a rework ect). Good luck!

Good to know: To order the new KESS sd card, please feel free contact at email sales@obd2shop.co.uk

KESS V2 v2.53 free download:

https://mega.nz/#!Lol0GCZR!nOeibBrssBZGwzzvHAlNozrMV3VkVWIl9P0zBT6dcIo

KESS V2 v2.53 installation guide:

How to fix XPROG can't read MC9S12DG secured?

Question: XPROG (both V5.5 and China clone 6.12) don't read all bytes. It reads only unsecured bytes (pages). I try Windows 7 32 and 64, and Windows XP. The insecurity zone is only FF. 

I think that problem is not in the ECU and connection, but in XPROG and MC9S12 secured MCU, because I read this MCU with VVDI prog without problems.

Post connection and ECU number Or Photo:

Good to know:

Advice: I think the data read by Xprog are OK, sitting at the right memory blocks but the final file size is much bigger than VVDI. 

For example, MC9S12DG256, Flash file has 2 MB of reading by xprog while just 256 if read via VVDI. Someone already compared these two data outputs, please?

+ 1: 

I did once. The size difference is because the Xprog reads the MCU like it was designed by factory. In the window where You choose the MCU family to program, You will see in info, that there are some addresses, that are excluded from memory. 

VVDI Pro and Rosfar read only the memory containing DATA, Xprog reads whole, as well as the blank (FF) spaces between data fragments. 

In Xprog ori software there is a button "Editor Tools" There is an option to convert the files. You can convert the 2MB file to the 256/521 and program with VVDI or Rosfar (it just deletes the FF from blank areas) and vice versa, there is an option to automatically add the blank spaces, and then program file from Rosfar or VVDI by Xprog.

http://blog.obd2shop.co.uk/how-to-fix-xprog-cant-read-mc9s12dg-secured/

Read & Write EDC16C35 with kess, ktag, mpps, Galletto clone etc

EDC16C35 ECU reading and writing tools review:  kess, ktag, mpps, Galletto clone etc.

Review 1. Kess v2 5.017 with red pcb

1). Read E60 530d EDC16CP35 with Kess v2 5.017 

Choose by Kline ==> Setup ==> Pull Up ==> 225ohm

takes longer to R/W but does it

2). Read/write Bosch EDC16C35 with kess v2 5.017 clone no problem.

3) Some of the clones works perfect some don't work don't know I got friend he bought kessv2 clone red and its not r/w some ecu he got problems

in my opinion kess 4.03 is best I never got problem with red 5.017 I got on some cars.

4) In bmw cars always good power supply to battery 13.5-14v and never problem to this cars 

edc16c31,c35 and cp35 all going good over obd and with kess or mpps.

today I tried it out, connect a good Battery Charger my Battery was at 13.1V and first Full read with Kess and than Write with kess.

Read 34 Minutes

Write 5-7 Minutes

Usw K-Line on E92 335D and in Options you have tu usw 225 OHM write speed.

Review 2. ktag via BDM

For EDC16C31 and EDC16CP35 I would done backup via ktag first.

you also can write with ktag via bdm... works fine at both.

Review3. with MPPS

- I Read/write Bosch EDC16C35 by MPPS and read/write by kess always no problem ... checksum correction OK.

- My car is BMW e60 530xd with same ecu as yours, and read it with mpps v16. Never write it yet. 

I think the kess is much better from mpps and you may not have a problem with it.

Review 4. Galletto clone works very good with this ecu via obd.

Credits to all users from DK / MHH forums. 

ECU programmers collection: 

https://www.obd2shop.co.uk/wholesale/ecu-chip-tunning/

Read write edc17c60 psa ecu with ktag clone

Read write edc17c60 psa ecu is possible with ktag clone, it is tested. 

No need to attach from underneath. Boot pin connection is next to tricore. You can find picture on Google.

Reading LAST ECU PEUGEOT CITROËN EDC17C60 GPT with Ktag clone V2.25:

Enjoy!

You can order ktag clone here:

https://www.obd2shop.co.uk/wholesale/ktag-v7020-red-pcb-eu-online-version.html 

How to fix the problem with nec adapter for upa?

Credits to @ PSAcars who made his contribution to all members having problem with nec adapter for upa programmer. After repair of missing line from R11 to J3, pin9 of IC1 to pin 24 of J2, giving and to pin 22 of 29F010 or 28C16 and giving and to J4 pin1 and J5 pin 1, he said he still have baudrate error. And one day it fell from the sky to me and he want to share it with you.

After a lot of work he found this. A line was connected to a dot that is passing to lear 2 of pcb. After that was cleared out, now the adapter is ok. He will give the bin file from 29F 010 and 28C16 if someone need them.
Today tested the 29F010 dump 100% working file.
upa nec adapter flash dumps.rar

Question: Can I write dump from 29f010 to sst39sf010a or someone have dump sst from working nec adapter ?
Answer: This is for you: Flash Cross Reference Guide

Note: This competitive data was obtained from public sources. There could be minor differences on AC/DC electrical spec and features. Winbond is not responsible for any changes or errors in this information.

Enjoy!

upa programmer
https://www.obd2shop.co.uk/wholesale/uusp-upa-usb-upausb-upa-usb-serial-programmer-full-package-v12-1277.html

ktag ecu wiring diagram needed

Question: does Ktag ECU programmer has ecu wiring diagram?
Answer: yes, in the CD. For those who don't have the ktag CD, please free download Ksuite 2.25 for ktag 7.020 on mega:
https://mega.nz/#!REpxwY5D!8FIo0maWqHbmEvHnTskmDVb68YLcZQQyoda5NHrapms
OS: Windows XP, Win7

The software contains ksuite software warnings, notice, recommendation, wiring diagram (how to connect, how to read, how to write...)

Images mean a lot:

Considering there are hundreds of Ktag ecu wiring diagrams in the CD that I can't attach them all here, I screenshot their names below, for anyone you need, please leave your email at www.obd2shop.co.uk for assistance.

Enjoy!

http://blog.obd2shop.co.uk/where-to-download-ktag-ecu-wiring-diagram/